大型艦船模型的制作完成不是一件簡單的事情，過程還是比較復雜且繁雜的，但是也會有問題出現，比如說模型變形了，這會是什么原因造成的呢？

　　It is not a simple thing to complete the production of large ship model, the process is still complicated and complicated, but there will be problems, such as model deformation, what is the cause of this?

　　所在地的溫差，是否有暖氣；；是放在展示盒內保存，還是直接放在空氣中；

　　The temperature difference in the location, whether there is heating; Whether to store in display box or directly in the air;

　　是放在柜子內，還是放在臥室客廳等溫差較大的位置；是否有陽光照射，還是有陽光散射到的地方，還是處于完全陰蔽；粘的PE的長度，制作前PE本身打卷情況；用膠量多少，是否粘在漆面上，如果粘在漆面上，有沒有用力按壓過，用的是液狀502點膠，還是啫喱狀502點膠。

　　Is placed in the cabinet, or in the bedroom living room and other large temperature difference position; Whether there is sunlight, whether there is a place where sunlight scatters, whether it is in total shade; The length of sticky PE, PE itself before production roll; How much glue is used, whether it is stuck to the paint surface, if it is stuck to the paint surface, whether it has been pressed hard, whether it is liquid glue 502 or gel glue 502.

　　大型艦船模型的船體是否有固定，螺絲數量和螺絲分布位置如何；注意一點對于全底銅柱固定船來說，艦首艦尾還是會存在一定程度的變形，千萬不要覺得全底船不會變形，無非全底船變形看起來不明顯而已，因此銅柱固定也要把兩個銅柱盡量分開一點如果是樹脂零件變形，底下浮空的地方是否有加強固定。

　　Whether the hull of large ship model is fixed, the number and distribution of screws; Note for the bottom copper column fixed ship, the ship first aft will still exist a certain degree of deformation, don't feel full bottom boat will not deformation, nothing but full bottom ship deformation looks not obvious, so the copper column fixed to separate the two copper bar as far as possible a bit if it is resin parts deformation, if there is a strengthening fixed bottom down space.

　　PE過長導致熱脹冷縮崩開，這里千萬記得一點，哪怕是塑料船，PE也是不能用太長的，像欄桿這種PE都要裁開，如果是樹脂則要求裁的更短。錨甲板也盡量換成膠板來制作，這樣甲板和錨甲板材質相同，粘在一起時才不容易因為熱脹冷縮原因崩開，不要用原件的長條PE。

　　PE too long lead to thermal expansion and cold collapse, here do remember a little, even if it is a plastic ship, PE is not too long, like the rail PE to cut, if it is a resin is required to cut shorter. Anchor deck should also be made by plastic board as far as possible, so that the deck and anchor deck have the same material and are not easy to collapse due to thermal expansion and cold contraction when they stick together. Do not use the original PE strip.

　　樹脂常見問題的話，就在底下鏤空/浮空的樹脂零件要注意內部填充或者鋼筋支撐，不然就可能發生不同程度的變形，輕則凹陷，重則扭曲。

　　If the resin common problem, in the bottom hollow/floating resin parts should pay attention to internal filling or reinforcement support, otherwise it may occur different degrees of deformation, light depression, heavy distortion.

　　如果大家制作完成的模型有發生變形情況（包括船體變形，長條PE變形，零件脫落，樹脂件變形等情況），不知道怎么的話，可以來網站m.zaiguo.cn咨詢。

　　If the completed model has deformation （including hull deformation, strip PE deformation, parts falling off, resin parts deformation, etc.）， do not know how to solve the problem, you can come to the website m.zaiguo.cn consultation.